Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
when i copied the spi_fujitsu_fram example to my project folder on c drive, i am getting this error "zephyr/linker.cmd:70 cannot move location counter backwards (from 0000c23c...
Hello!
I would like to know if there is any way to route the signal from the main LED from Nordic Thingy 52. I checked its data sheet and I only found the pinout for other...
After downloading nRF5 SDK v17.0.2, I checked the Release Notes - and they state SES v4.50 has "been used for testing".
So I downloaded & installed SES v4.50
The HID Keyboard...
Hi, recently I want to establish a connection between two development boards (STM32F103 + nRF52840-DK), that the STM32f103 board can create the data and send it to the nRF52840...
Hello, I have a project running on a PCA10040 board, using softdevice 132 (0x9D, v5.0), ble and serial port for data transfer.
I want to migrate this project from this...
I am trying to use the UART for a custom version of the DFU. I have it transmitting no problem, but I never get the RX_DONE event. I cannot see any reason and I have looked...
Hello,
I have a question because there is a problem with writing code using timer.
I wrote the following code to avoid using the LED timer when I first ran it.
However...
Hello Please help. I want to connect ble central to a specific address. And the ble peripheral has a ble central address, that can connect to it. 1. Is a whitelist used on...
hi,all
i am a new learner about the BLE
when i use softdevice 17.0.2 to run the example (anyone) ,there is no problem.
then I want to use the SDK12.3.0 to run a formal...
hi
I am using nRF52832 and mesh sdk V4.2
I have modified the light switch example in order to send 1 byte of data instead of the on-off commands. in the server side I...
Hi,
I have a problem with coap response. I use iot coap library.
Client send nonconfirmable coap message with payload to broadcast addr
Server get payload and send nonconfirmable...
I am getting the Following error after connecting the JLink
I followed the following procedure
What am I doing wrong? DO I need to install anything else?
Hey All,
I ran into an issue on the nRF Connect SDK trying to get a nRF52840 advertising using CODED PHY. I figure it's not fully implemented yet are there any updates on...
I advertise as
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED
This posts suggests I may have not really disabled...
