Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello, I would like to get data from the advertising packet. I think that utilize this function is a good starting point :
Then ... For exemple, what do I need to do to...
HI ,All
I want to update the data at the same address in nrf52832 flash. What should I do? Do you have an example program? If you have, please send me a copy
Thanks...
Hi, I am designing a central using nRF51422, SDK V11, S130V2.0.0, modifying the central example to connect to a Ammicom BLE module of a product. After the CONNECT_REQ is sent...
Will the nRF52840 eventually support SPI speeds greater than 8 MHz? Will a preview / reference board for the nRF52840 be released with support for these higher SPI speeds...
Hi,
I am trying to set up a slave select on P0.28 but I noticed it's not driving high. I've tried several settings and I'm now using the example from https://devzone.nordicsemi...
Hi,
I am working on NRF52840 soc with SDK 15.0. I am trying to advertise beacon adv to long range. But i got to know that non connectable long range Advertisement not possible...
Dear Nordic Team,
Thanks for supporting.
hardware : PCA10028 (DK 51)
Software : SDK12.3.0 ( NUS example )
Secure DFu implement with NUS example it is compiled and...
I developed one project using BMD-300 Evaluation Kit that include nrf52832 microcontroller. In my project, I use the nRF5_SDK_14.2.0_17b948a and s132_nrf52_5.0.0_softdevice...
Hi everyone,
Using the SDK11.0.0 development product, it was found that the 52832 restarted randomly, with a reboot time of 7 days or longer.
App code condition:
1....
Hi guys!
First of all, sorry to make this question here because it is almost unrelated to Nordic, but I am desperate. I developed a device using your nRF52832. I programmed...
Hi,
I have a problem with Thread network stabilty and formation in new SDK for Thread and Zigbee 1.0. Examples seems to work fine in unchanged form, network is stable and...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
