Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
We have using nrf5340-nrf7002 in our custom board. SDK version 2.6.1 We understand that the timer will not function in System OFF (deep sleep) mode. However, our project is...
Hi there,
I've encountered a strange PWM behavior and have investigated a bit. When setting load_mode to NRF_PWM_LOAD_WAVE_FORM, creating two sequence, and the latter sequence...
Hello, We want to build our own custom protocol because the features we need are not available from existing protocols like BLE or Zigbee etc. But it is beyond our reach to...
Hi all,
In my application I need to use some of the NET core peripheral from the APP core (since I ran out of peripheral instances in the APP core). According to this page...
I am running into an issue (title), where I am attempting to switch the advertising interval to a slower interval after a set period of advertising in order to save power...
Hello everyone,
I'm trying to test the ble_app_uart example. When I download the code into the 52DK, i can see my device show up as a possible connection, but when i connect...
We have a number of fixtures using nRF52 DK boards to both flash a custom board and to do a DFU operation to that board. We use a SPST switch in the P19 pin 1 lead in the...
Good day
Our custom board contains RS485 implementation. The file schematic for that looks like this:
I have noticed that a driver and sample exists but the driver doesn...
Hello everyone, I'm currently updating my project from SDK v10 with softdevice S110 to SDK v17.1 with softdevice S132 (a huge step). I'm, wondering if what I want my code...
Hi
I am trying to make a SPI connection with a device which doesn't already have a driver build into Zephyr.
Is there some kind of genereic device i can use since i just...
Hello,
I am trying to send data from a delta-sigma 32 bit ADC - the front-end is an EEG amplifier - via WI-FI to my broker. I would like a recommendation related to the...
Hi,I am using NRF5340 AUDIO DK BOARD and I have been trying to access i2s mic and I want to transfer the mic data to Amplifier .Is it possible to do with single I2s ? As I...
Hello everyone,
I'm experiencing some issues while trying to program an nRF52832 CIIA on a custom PCB. Specifically, I cannot get the GPIO pins or the external 32kHz crystal...
Hi, I checked DFU over Wi-Fi in a separate project (net/download) that only included DFU and Wi-Fi-related functionality. In which FOTA is working as expected.
In our custom...
I have just started programming the using the nrf52840DK_nrf52840. I downloaded the toolchain and sdk using the VS code extension and created a new application from the blinky...
