I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello Nordic Support Team,
I am currently working with the Arduino Nano 33 BLE (ABX00030) , which features the nRF52840 SoC , and I am interested in accurately measuring...
I want to read the RSSI. The code is shown as follows: ，However, after compilation, the error message displayed is: "undefined reference to `bt_hci_cmd_alloc'".I need to know...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
Hi,
I have been working through the Dev Academy cellular course using the nRF9151 DK which is fitted with a 1NCE MFF2 eSIM. I was able to set this up in the Board Configurator...
Hello Team,
I am using the nRF52833 with the nRF Connect SDK (v2.9.1) in VS Code , and I am experiencing an issue with the RTC calendar update.
I initially set the RTC...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
Hi, Recently we upgraded to nrf-sdk 2.7.0 (previously on 2.6.1) and I began to notice that NFC had stopped working for our project, when running on nrf5340dk.
While switching...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I am attempting to learn and integrate full modem FOTA functionality into my application...
Bonjour,
We are working on a firmware upgrade for our product based on a nRF52833.
With the previous firmware, compiled with SDK 2.3.0, when the board was OFF, the power...
