The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
I am trying to define a pm_static.yml file which will use the 512K ram on the nrf7002dk_nrf5340 for the TFM ram section.
I cannot compile the non-secure nrf7002dk...
Hi, I got my nrf54L15 DK, but i can't start RTT logging. I set this configs:
CONFIG_PRINTK =y
CONFIG_CONSOLE =y
CONFIG_RTT_CONSOLE =y
CONFIG_UART_CONSOLE =n
CONFIG_USE_SEGGER_RTT...
Hi,
Is there any ongoing development for a PPK3 ? If so, what is the timeline for its release ?
Some features requested in previous posts:
- Voltage measurement
-...
Hi,
Could you please clarify why there is an override of the checking rules in https://github.com/nrfconnect/sdk-zephyr/blob/ncs-v3.1.1/drivers/timer/Kconfig.nrf_rtc#L6C8...
We are developing a custom board with an ADC device that supports QSPI. Our application requires throughput speeds only available using QSPI.
All the available driver examples...
Hi,
I would like to use existing development setup (for STM32) :Visual Studio 20XX (not VS code) with VisualGDB plugin to work with the nRF9151 Development Kit.
However...
Hello, I have a project implementing the ASYNC UART API as laid out in the Nordic Development academy exercise. I had this successfully communicating with an external device...
Hi,
I run a couple test with the PPK2 on our board to measure and optimize the power consumption, but I had some weird results and I'm hopping you can help me out to understand...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hi,
I can't program nRF52840 dongle using Programmer Tool on Linux.
Dongle is visible, can be selected and memory content read without any problems but file write attempt...
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
Hi Team, We are facing significant range issues on iPhones and other iOS devices with our hardware. We have tested these with both Custom App ( Made in House ) as well as...
