I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
Hello,
I am developing a remote device which uses system off mode for idle state. I also have the condition where extra long press of any key that is beyond the long press...
My Peripheral is using the ble_conn_params module. I'm seeing that if my Peripheral calls sd_ble_gap_disconnect() soon after making a connection, the module will sometimes...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
Dear all,
I am using the following peripherals in our product.
1. TWI Sensor
2. BLE
3. APP timer (1. to poll a gpio pin & as RTC)
4. SPI flash
5. 2 Edge sensitive...
Hi,
I am using nrf_queue to store data in queue which is inserted with time based interrupt at several milliseconds. Also same data from queue is fetched at bulk.
I am...
Hi,
I have modify a BLE program from ble_app_uart by using SDK 15.3, but the system will crash when I do following test:
Please find attach file for my code.
Step1...
I want to double check current draw in the nRF9160 low power modes and need some help in making sure I know how to do so.
I plan to use an oscilloscope for measuring current...
I hear that the GPS should now work with the onboard antenna of the nRF9160 DK for versions 0.8.5 and later. I also read that the asset_tracker application has been updated...
Hi All,
I'm referring to generic on/off ble mesh example code and we are in the development stage.
I would like to know which pins are used for PA and LNA in the example...
HI
In our application we are using "app_sched_event_put" function but its showing [NRF_ERROR_NO_MEM] when i debugged it please look the screen shot.
The sdk we are...
Hi:
for "ble_app_hids_mouse" example ,it has SWIFT_PAIR_SUPPORTED.
Does HID_keyboard also have this feature?
Could I move swift_pair from "mouse example" to "keyboard...
Hi,
I have an ADC which is interfaced with the nrf52.
The samples from the ADC are collected every 2ms (500Hz sampling rate). I store these samples, and when the number...
