I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
When I change ATT_MTU size and add the following code:
#define CONN_CFG_TAG 1
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg));
ble_cfg.conn_cfg...
How do you do
Now use the Nordic nor51822 \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this routine plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples...
Hello,
Am working on NRF52 interface via SPI to Micron N25Q flash .
Am able to identify flash by reading chip identification correctly and after this to test memory writing...
We are a small R&D team and we are currently developing a medical wearable. We are using nrf52832 and we are generating approximately 54kbps (6.75kBps). I 'd like to ask if...
Hi!
After reading few posts about spi slave/master issues... I'm also challenging with one of them. I have following setup nrf51822, s130 2.0.1 and sdk 12.3.0… nrf51 (spi...
I am working on OTA DFU about nRF52810.
My refernece project are ble_app_uart\pca10040\s132 and bootloader_secure_ble\pca10040
I find that the RAM start address between...
Hello im trying to create a single master connected to multiple slave to make synchronous movement for my robotic arm project but im not entirely sure which Bluetooth to consider...
Hi,
I am running the BLE DFU example. I am able to perform the DFU OTA implementation successfully. The problem I am facing is that, once the application has been updated...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello,
I used translation software.
I am measuring current.
I want to enable dc-dc mode.
how to enable the dc-dc?
also,where should I change the source code?
I...
Hello folks, we are currently using RedBear Lab Arduino toolchain to develop a MDBT40 based application. However we meet a lot issues on merging bootloader.hex (downloaded...
Hi,
Since I'm having a hard time understanding this through the SDK docs, I'll ask it here.
I'm currently using a BMD200 module (from Rigado) which uses a nRF5188.
...
I have a BLE-Nano v1.5 board with 32KB of ram starting at address 0x20000000 (til 0x20008000). However when I want to read a byte of the uper 16K (0x2004000+), I get a 'cannot...
I need to scan for nearby beacons.
This was featured in the mbed examples but does not seem to be described anywhere else
I am using SDK12 at the moment.
I found the...
hello
Now I use the nRF52832's board and I was measuring the current
But when the board's power is off and i measured, the current was flowed in the board.
Now i am using...
