Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi!
I have a question about the Mesh SDK. Is it currently possible to get the physical source of a relayed message (thus the relay that send it) out of it? I only seem...
I use buttonless_dfu_app as template. SDK 14.2
Q1. Could someone help me.. After I updated my app I have changed crc (if more than just few changes), so bootloader installed...
I made all steps in a guide
devzone.nordicsemi.com/.../
All works fine. After that prepare my own firmware like appendix 1. Also works good. I merge
bootloader_setting...
Hello,
i'm trying to run the ble_uart_example on my nRF52840 eval-board, but it always fails on this line:
err_code = ble_advertising_init(&m_advertising, &init);
APP_ERROR_CHECK...
Hi, everyone,
I develope the project with BLE support. In my project I need to define the time server. For this purpose I tried to find any example reffered to it, but no...
It is a sensing-processing-actuation based application. Just want to use the nRF52832 module for BLE communication( a part of the application).
Is there a direct API in the...
Hello,
I have an application where an nRF52832 peripheral (S132 v3.1.0) transmits a 5-to-10 MB file to an nRF52832 central (S132 v4.0.5). The peripheral sends the file...
Hello,
I have bought an nRF51 dongle with a SEGGER J-Link.
I have downloaded all the SDK and everything from nordic website.
If i open an ble peripheral example in uvision5...
Hello i cannot get uart to work correctly on these pins. The board seems to reset when i try to run uart on these pins. I can get them to work on pins P0.06 and P0.08. I think...
I could not find update info on this;
When I use mergehex to combine SD, app and bootloader, MCU just boots into DFU mode.
When I program SD, bootloader and app, MCU...
I have a nrf52832 running as a BTLE peripheral running up a couple of services including one custom with a characteristic i wish to be modified by the peer.
Data is being...
Now I'm using NRF52832 to communicate with other MCU(STM32) by UART.
STM32 will transmits about 40 bytes data to NRF52832 per 10ms.
Here is my configure referenced Nordic...
Are there any dependencies between the connection parameters configuration and pairing?
I am using nRF52840 and SDK 14.0.2 and ATT_MTU example. I am trying to add pairing...
I am trying to implement bonding with the Uart example in SDK 14. I have followed the instructions for how to use implement device manager and then migrating to peer manager...
