Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello everyone, The last few days I was advised to buy the nrf52840 DK. Up to now I have worked with the dongle. I read online the need to download the j-link software. Where...
Currently, I'm switching my platform form nRF52 to nRF53.
For the work I'm doing, I need to use DPPI to enable GPIO events to trigger SPI transmissions, without interrupting...
Hello,
Looking for some background info for SOFTDEVICE ASSERTION 0x0002715e. sdk 15.3, SD s132_nrf52_6.1.1
Maybe related, there is no Assert if fds_record_write() is done...
Hello
I am developing devices including nrf52832 and 3.3v buzzer. However, the buzzer in this device is very hot and the battery is running out quickly.
Now I know that...
Hi. I always appreciate to your kindness and fast reply.
I want to extend BLE range from 200m ~ 500m using FEM.
For the first time, I choose SKY66111 but it is not working...
Design background and goals,
1.Both ble_central and ble_peripheral are used nRF52832.
2.All nRF52832 UUID are the same.
3.Devices of different groups can’t be connected...
Hello!
I am having a problem using any internal flash writing libraries. If I set the REG0 voltage to 2.7V, the controller stops erasing the memory.
Moreover, I cant erase...
Hi,
I have seen that the pin for nRESET is selected on the NRF_UICR->PSELRESET register. I know that it cannot be modified from 0.21 on the 52832.
Can it be modified on...
Hi guys,
I am trying to figure out how to send the sensed data (temperature value) from the LPN node to the server node in the BLE mesh network. I have already found this...
I am using the nrf5340PDK and i am trying to have P1.04 trigger an interrupt on a high to low transition.
attached is my overlay file and my main.c to initialize the GPIO...
I made a code based on ble_app_uart_c which connects to a peripheral and once connected it can write or read data.
The code is supporting BLE4 (1M) and BLE5 (Long Range...
Dear Concern,
we have tried to configure the accelerometer LSM6DSO module through SPI interface using NRF52xx DK board. External Module was not configured properly...
