Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
The function documentation for pm_conn_handle_get says BLE_ERROR_INVALID_CONN_HANDLE is set to the connection handle pointer if the peer is not connected, however it is BLE_CONN_HANDLE_INVALID...
Hi,
I programmed nrf52840 dongle with simple ble_blinky example. The dongle successfully bond with my phone but when I tried to discover services and read characteristics...
Hi
I am working on nRF52832 DK and using Ubuntu 16.04 and Segger Embedded Studio as IDE. When I try to build the AES_CTR program, the following error comes up.
Can anyone...
Hi I have run a few peripheral examples ok and now move to evaluation of ble_peripheral also.
I'm using this version of the SDK....
If I program the softdevice and...
Hi
I am using Segger Embedded Studion on Linux 16.04 operating system. I have programmed softdevice, i.e, I have provided SRAM and FLASH START VALUES and other things. How...
Here is a list of problems I found. Please fix them.
nRF SDK 15.3
Examples: logging does not work in examples. I think the problem is related to this issue .
Documentation...
Hi there,
On my application, I have multiple sensors attached to the nRF52 and I read them every 5 seconds scheduling the read inside a timer handler, then when the Softdevice...
Hi Nordic Forum!
In the past, I set connection interval min to max is 20ms~75ms, it work ok for IOS。But on Android platform, Android use 75ms as actual connection interval...
Usually if i am making C Program then i just include the library and get on to the code using documentation. this is same case when i am using STM32 , Samd and esp32
but...
Hi
For a project I want to send acceleration data via BLE 4.2 (with DLE). An acceleration packet consists of 81 values (24 bits each, total 243 bytes). My goal is to send...
Good day
I converted a Central UART example. I thought I would experiment with the "sd_ble_gap_tx_power_set()" function to see how it works.
When I include the following...
nRF5 SDK v15.2.0, nRF52840
This issue occurs on reset, most often after cycling power.
There are 4 pages reserved and 4 data pages are found. Since a swap page isn't found...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
