I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
When I try to update the application on the nRF51422 chip over DFU, I have trouble with the bootloader.
I use the nRF Toolbox app to do the firmware update. I can select...
Hi guys, this may be a lame newbie question, but I was unable to add a driver to my uVision project. For instance, I've opened the ble_app_template and now I want to include...
In the reference designs, the inductors in the antenna circuit are simply referred to as "High frequency chip inductors". Do you have any example manufacturers part numbers...
I'm testing my nRF51822 Bluetooth Smart Beacon Kit (pca20006). I've successfully uploaded ble_app_beacon_bcs code example to my beacon via Master Control Panel Android app...
hardware:pca1001
software:s120 v2.0.0
sdk 6.1.0
i will get rssi value by connected by s120.so i update the s120 to v2.0.0. but when the app run,
an error occur.[APPL...
Hi All,
I tried to use the nRF51422 device UART RXTO events using nrf51 SDK v6.1.
I set the NRF_UART0->INTENSET in app_uart_init() as following:
// Enable UART interrupt...
Hi, I have just managed to successfully read ADC values and send as a service but they are in uint8 format. Is there an easy way to convert this to decimal within my adc handler...
Is there provision for a serialization application processor to control GPIO on a nRF51822 used in serial connectivity mode? Can the nRF51822 be used as an I/O expander?
Hi,
I want to simultaneously read the value from 3 analog pins. For this, do I create just one adc_init function and handler functions or do I need to create multiple initializing...
Connections to my peripheral device are generally very short. I don't really need to have my device request a connection parameters update.
Does this mean that I can safely...
I purchased a pair of FTDI cables, and I can't seem to get them to work.
Unsure if the pinout is standard but here is the mapping of the cables provided:
Red wire： 5V...
I am using the N548 with the S310 soft device. I have set up the device for asynchronous communication via the UART. I can send ANT+ commands via the UART and I get valid...
Hi there,
I am quite new to BLE.
I am about to buy a nRF51822 Bluetooth Smart Beacon Kit. But before that I would like to be sure if I am able to advertise battery level...
Hi,
We just recently received our (custom) board with the nrf51822.
To program and debug the nRF I use the pca10028 and the debug out header.
I wrote a very basic program...
I tried loading SoftDevice, Bootloader, and Application using the SoftDevice and Precompiled hex files that come from the example code version v1.1.0. I am using nRFgo Studio...
