Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm trying to use RTT for debug printing and having some trouble. I'm using the nrf51-ble-app-lbs example app that goes with App Note 36. I've added the RTT code from www...
Hi,
iOS device uses random private resolvable type changes own bluetooth address address every 15 minutes as long as I know. Can I see the transittion just to change the...
I see the python S110 bindings (via SWIG) have been made; it was pretty easy to get the demo code up and running, many thanks! Any chance that S120 central role bindings can...
I have a custom board with an nrf51822 device. I also have Keil 5.12 and a ULINK2 and would like to program softdevice hex file into the nrf device. I have followed all of...
I'm trying my best to get started w/ the nrfgo 51822 development kit that I got last summer, but I'm just having a hard time jumping in.
I was a little disappointed to...
I need to use a high speed PWM (> 500 kHz) in which I can vary the pulse width. In examples, it's handled in software which is too slow.
Is there any way to set a pin on...
Hi,
I am having some problems getting the s110 SoftDevice working (sd_softdevice_enable stops the program execution) on a custom PCB. I have seen several issues similar...
Hello,
I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated...
I'm interested in getting started with NRF51, but the full DK is quite expensive here and I don't need it. Does the nRF51-Dongle sku come with a key for downloading & using...
Hi,
Can someone tell me (definitively) what the max SPI clock speed is?
I have seen 2,4 and 8Mhz here and in recent documentation and I'm confused.
Thanks
Hi
I have been experimenting with encryption and bonding and I think I don't understand completely the bond procedure.
To bond a device, it is necessary using the bond...
HI ,all !
I have a question about PORT event function.
as the 4 channels of GPIOTE (channel0 to channel3 ) have been used for other usage.
i need to use a general IO...
The only documentation I can find for s120 is part of the nRF51 SDK . Though it isn't clearly stated the SDK assumes release 1.0.1 of S120 is being used.
The v2.0.0 S120...
Hi
I got some questions about KEIL MDK uVision5.12 PACK.
I tried uVision5.12 PACK to install Nordic SDK package. Currenly, their latest version is v7.1.0.
If...
