Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I See in the discussion that I can see I/Q for AoA.
I see this examples "direction_finding_connectionless_rx" on zephyr I Think that I can start debug using the data from...
I want to transfer a few bytes of data between two NRF52 modules.
I have checked out the BLE Blinky and NUS example and understand the gatt client and server ideas.
My...
Hello.
I am using SDK version 17.0.2.
The example code uses nrfx_spim . Target board nrf52832
The nrfx_spim project confirmed that 10040 did not exist, only 10056...
hello,
in the case
Case ID: 227777
https://devzone.nordicsemi.com/f/nordic-q-a/46439/turning-services-like-hid-on-off-without-disconnect/309149#309149
In the...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
I am trying to establish a tunnel from ZigBee client to ZigBee server on nRF52840 using "nRF5 SDK for Thread and Zigbee v4.1.0".
Starting with the examples "examples\zigbee...
Hi everyone!
Challenge :
I'm trying to stream data from 9 nrf52832 (12 bytes each) to a computer, hopefully at 25 Hz at least (it seems more than realistic!).
Dream...
Hi !
I want to send simple HCI commands, such as reset, to the nRF5340 via UART. Therefore, I'm using the sample "hci_uart" available with nRF Connect SDK v1.5.0. I am sniffing...
It would be great to get some reassurance on this design. Is it ok for production i.e. is robust and within limits?
I am successfully driving an smd rgb led by sinking 2ma...
I am using the https fota, aws sample OK.
testd the aws certificate via Linux PC this way:
openssl s_client -connect kamacodeetrog.s3.us-east-2.amazonaws.com:443
now...
