I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi,
Recently I was able to get a single read and write SPI operation to work properly with a custom nRF52832 (BL652) with SPI connection to MCP2515 (CAN SPI) using the nrf_drv_spi...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am attempting to import an existing IAR project to SES / GCC and am having some trouble. I recently joined the project team and we are making an effort to switch from...
Hello,
So I'm trying to modify the mqtt_simple sample program to connect to azure iot
I've modified the code in a few ways but when I went to run the program it gave me...
hello,
below is the error experienced.
nrfjprog --family NRF52 --eraseall ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run the...
Hello,
I'm using a nrf51422_xxac_s110, with the Keil uvision IDE. I recently upgraded my sdk from an older version, to 12.3 in order to use some components like FDS. Consequently...
Hi guys, I'm using a HFCLK TIMER to time ADC sample capturing via PPI. This eliminates CPU+BLE usage from affecting my time keeping. I assume that each ADC sample arrives...
Do you why I could not pass the "ble_stack_init()? I did download softdevice from 0x0000-0x26000 and Application from 0x2600
int main(void) { // Initialize. log_init();...
I can run some of the samples on my nrf9160 DK, however when it comes to this one I get a assertion error err==11 that I have not yet been able to solve.
ncs/zephyr/subsys...
Hi,
In my application I need accurate calendar capabilities such as alerts on every hour and alert on a specific hour every day. Is there any implementation of such a mode...
Hi,
Want to read data from HX711 adc amplifer with wheatstone bridge loadcells, but when i run the program, my output is <info> app: ADC measuremement -8388608 all the time...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
