I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I have compiled and debugged the temperature_pca10036 code from nRF5_SDK_v11.0. I have used termite terminal for getting info about transferring of data from nRF52832 board...
Hi,
I am using nRF52 board and want to change the RESET output from P0.21 to P0.2.
-I have CONFIG_GPIO_AS_PINRESET defined in the makefile.
-When debugging I can...
First, we implemented ble secure dfu application on nrf51dk. After, we want to program nrf51822xxaa device with same ble secure dfu app. In addition, we saw about rom/ram...
Hello Friends,
I've Get my Thingy from Nordic Tech tour and have a good time with it.
I think everything is perfert, but location of ccs811 ( Tvoc +eCO2 Sensor ) is...
Hi Nordic & friends,
As I know, DLE(data length extension) is not supported in S112. We are using nrf52810 in our development, so I make a test.
A long data packet(>=20...
How can I perform multiple A / D conversion?
I created a program with reference to the method of the old version of A / D conversion, but the function name and argument used...
Noted that the new V15 SDK for IAR does not have linker config file set correctly on ble_app_blinky_pca10040e_s112 project. The .intvec start location was set to 0x19000 and...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
Hi There,
I have been looking into how to connec my QSPI NOR Flash to the NRF52840.
I have notivced a discrepancy between the comment in the Table 3. of the OPS and the...
Hi,
I have a peripheral which sends data to the central and from central i n eed data to be send to Mobile App
is it possibe to do and how???
or any other ideas you...
I am using Keil 5.24.2
I already downloaded and compiled with build_all the micro_ecc. Having no issues here.
According to the error, and what I read in another thread...
I have been investigating the possibility of using the QSPI external flash peripheral on our NRF chip. After doing a typical qspi read command, the external flash chip would...
Hi,
when i make a connection to my device i get 4 `BLE_GAP_EVT_CONN_PARAM_UPDATE`.
If i make an action of read or write when update event occures i get a duplicated read...
