In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi,
This is my first post here. I hope I will follow the structure of a good question.
I want to have a sequence of defined duty cycles (let's say 4 values). The aim...
serial-rtt.zip I'm having trouble debugging SDK14.1.0 example serial using NRF_LOG with NRF_LOG_BACKEND_RTT_ENABLED using the NRF52 DK, PCA10040.
With NRF_LOG_ENABLED set...
Situation: Trying to upgrade previous versions of the SD and BL (V3.0.0) to (V5.0.0)
Problem: device power cycles after a new application is flashed to the device into the...
I have successfully managed to communicate back and forth ( message ,Temp and Humidity data) between Two Arduino Nano using NRF24L01 module. However when I am trying to receive...
Hello All,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART i changed the uart pin configuration as...
dear nordic employee:
I want to use the PPK measure my hardware
I set as the 《PPK_User_Guide_v1.1》 says,and the led1 is ok
but the ppk cannot work well
the details like...
Hello! Is it possible to subcribe on more then one characteristic (which support NOTIFY) on nRF52832 (in Central role)?
I check it in nRF Connect app, it's working, so probably...
Hi，i use SDK13.1 and nRF52840.I keep the DFU_APP_DATA_RESERVED equal to the FDS_VIRTUAL_PAGES.When i change the pages of them to 200,OTA was broken off when starting DFU.When...
SDK13, S132, nRF52832.
I use whitelist and bond peripherails. But after bonded 20 pcs of peripherials, I can work with only first 8 bonded.
Which parameters should change...
I’m trying to create a nRF8001 device without the need for any keys, because the device will be inaccessible in mounted condition. Additionally the connection must be secured...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
Hello Sir,
we have designed custom PCB using nRF52832, I am little confused for is it OK. I have attached top and bottom layer layout of my PCB please sir review it and...
