I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
We have a custom board with nrf51822 chipset, when i try to flash ble_app_proximity application through keil, it is giving advertisement, but i cannot able to connect...
I have a custom PCB and i have connected the MISO,MOSI,SCK,REQN and RDYN line from the nRF 8001 to Arduino. And uploaded your code of ble_uart_project.ino but nRF 8001 does...
Executing:
nrf_gpio_range_cfg_input(0, 39, NRF_GPIO_PIN_NOPULL);
I believe it will.
I know the range should end at 30 but I hit the wrong key when I coded it. So...
I have a characteristic that is 80bytes long which is sometimes read by the client using long read. I also want to send the complete attribute value when its state changes...
Hi guys,
i tried to find information about the differences in chip revision
nRF51822-QFAA-R7, NRF51822-QFAA-T and nRF51822-QFAA-G0 but i can't find the R7 or T type anywhere...
1.
Are there any other resources than RTC/WDT requiring 32kHz LFCLK, not listed in Table 28 of nRF51422 PS (i.e. Radio)?
2.
ANT stack requires LFCLK +-50ppm, so +-25ppm...
Hello,
I'm getting an exception while starting MasterEmulator Sample Programs. All indicated Dlls were copied along with .exe, windows ver is 7. the same error happens...
Hello all,
I would like to send Acc and gyro data just like health temperature over nRF8001. Which Service can I use? How can I create one?
Thanks for help in advance...
I have BLE Shield V2.0 and i want to change the device name from the iPhone. We can use nRFGO Studio to change the name from GAP Settings but this is only one time change...
When using proprietary radio protocols only (Shockburst/Gazell) are there any difference between nRF514 and nRF518 chips? Do they behave totally equal so they can be used...
I need to send a data package when radio is ON every time
but I try to send data by "sd_ble_gatts_hvx()" I find it can not work,it seems that I can't call this API to send...
Hi
i'm new in dev zone and i have a question
now i work with nRF8001 and i want to design a pcb for it.
I want to reduce the BOM and for this i want to use only the internal...
Hi,
I am trying to use the DFU example provided in SDK 5.1.0. I have built the example using gcc 4.7.x, and i am also using softdevices 5.2.1. The DFU example has been...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
