Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
I should not be asking this question here but it should be documented! SoftDevice s130.
A possible error I can get when executing sd_mutex_acquire() is NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
I am using the SHT21 sensor for measuring temperature and humidity, trying to connect it to nRF52840 DK Board using TWI mode.
I am unable to even scan and get the response...
I deleted the flash completely for the bootloader example, then I installed soft device. The softdevice area for nrf52832 is written as 148 kb in the documents. In nrfgo studio...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
