I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
We ared esigning a new board with nRF9160 and nRF52811, We want to be able to do FOTA (modem- and app) for the 9160 via the 52811. Are there any special considerations we...
Hello, I am having problems getting the TWI to work. The NRF52810 needs the TWI to communicate with a EEPROM module.
Thus far ive set:
Then I try to do the TWI Scanner...
Hi,
I would like to connect the nRF52840 JTAG to a debug probe in order to debug and program it.
Can I use any debug probe or a specific one is mandatory?
Thanks...
Hi,
i am working on sdk14.2 in SEGGER EMBEDDED STUDIO, i am trying add some file to ble_app_blinky_pca10040_s132 example at the time of compilation i am getting linking...
I have run into a problem compiling with ARM Compiler 6 version.
In this case I cannot figure out the problem.
Seems the only file causeing problems (after fixing a few...
Hi
I am using SDK V. 15.3.0 and Softdevice S132 6.1.1 on a nRF52832. I am developing two devices, one of with is battery powered and one that is connected to a serial interface...
Aside from the connection interval, I'd like to know if the 2Mhz phy is enable along with Data Packet Length Extension and Connection Event Length Extension.
Is there...
The modem_info module in nRF Connect SDK returns various modem parameters to the application. The function "modem_info_params_get" fails to update the following paramters...
We are running an application in dual mode (central + peripheral) where we relay the data from the peripherals up to the top central. Is it possible to control the priorities...
As a user I need to include stdbool.h before including lte_lc.h. lte_lc.h uses the bool type but does not include the appropriate header, so I get compilation issues if I...
use sdk:11.0
Reference routine：ble_nus_c
now I use 52832 to connect a device,the service UUID like the photo.
when I only discover one service UUID,like this code...
I am using an ADC where the SPI MISO pin also acts as a data ready pin when it transitions from Hi-to-Low as detailed in the link below. I am able to configure this and it...
