Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I'm working with UARTE using a receipt timeout. So far so good, I tweaker nrf_drv_uart to get notified upon RXDRDY interrupt (char received but not yet DMA transfered...
Hi,
I've got some software that already uses nordic_uart, so when I try to add another uuid I get NRF_ERROR_NO_MEM.
Now reading around at others with this problem, it...
Dear Nordic,
I am following this test example [https://github.com/NordicSemiconductor/nrf51-ble-app-lbs/tree/throughput-test-5.2.0] while using nrf51822 dev board.
I...
Hello.
I use nRF52 , PCA10040 , S132 , SDK 11 & Keil5.
I want nrf to do bit operation.
The code about bit operation is following.
unsigned char tmp[2];
unsigned short...
Dear Nordic Team,
Thanks for support.
I try to enable dfu service in proximitty example code as per the nordic document .
But its not work. I dont know what i am doing...
To the wizards at Nordic,
I come to you with a rather perplexing issue, we are building a custom application on top of our nrf52 based design. The board seems to work great...
I think similar issues have been posted before and not resolved
If I flash the hex precompiled hex files for virtually any project by using the pca10028 S130 version it...
Hi, I want to detect long and short press in same button. Define "BUTTON_DETECTION_DELAY" can detect one delay. Let me know to detect more than two delays.
The same question...
hi,
i am working on blinky example code. i was build the code and generated hex file using Eclipse IDE. i have nrf51822 ble module.
want to flash the hex file using dfu...
Most of the make files and project files within the nrf5 SDK contain a bunch of defines of the form -DNRF_PAN_XX. A search through the SDK v11.0.0 reveals only a few references...
I have included all paths of all (.h) files including (nrf_delay.h) however I got errors as seen in the photo. What do you suggest to overcome such errors?
Also, Is the following...
Hi,
This is very newbie, and I am stuck.
I am following to the letter the instructions to create the micro-ecc according to this instructions.
The problem, and it...
Hello,
I want to use packet length extension with the PCA10040 and SDK v12.
The peer will be the nRF51 dongle (PCA10031).
I believe that the nRF51 dongle doesn't currently...
I am still noticing a higher than expected power draw on my nRF52 and I want to make sure I have adopted best practice in turning things off/optimising things before entering...
