Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi!
As a student, I am starting a new project on university. Project is based on beacons idea, so I decided to use Nordic's chip as an MCU.
I am trying to decide, which...
Hey folks,
I am going to join Nordic Developers community, but before I can do that I need your help.
I am quite familiar with software development, however, embedded...
Hello,
DFU issue (FOTA application update fail)
I have a problem when performing Application update over the air , after i change my boot loader.
so when try FOTA...
Hi,
I am using two Android devices with nRF Master Control Panel (BLE v4.0.5) app installed on both. I am using one Android device (Moto G 3rd Gen Android v6.0) as the...
Hi all,
I see that the nRF51 doesn't have a PWM module and a software PWM library is needed. How well does the software module actually run? I've had rather bad experiences...
I have a new nRF52-DK (PCA10040) and I'm trying to make some examples using arm-gcc. With freshly downloaded nRF5_SDK_11.0.0_89a8197 and Makefile.posix modified to point to...
What is the status of I2C pins and GPIO pins in the System OFF mode? Do they float once the SOC enters SYSTEM OFF mode? Here the accelerometer we are using consumes high current...
I tested Auto connect with NRF52832 UART APP(S132 softdevice), and nRF Master Control Panel APP.
I tested with samsung s3 neo and Moto G3 , but it is not working. In which...
I am currently using the watchdog in conjunction with RTX and a softdevice on the nrf51.
I am wondering if the default priority for the watchdog's interrupt works well in...
I am simulating button presses on a peripheral nRF51 device to determine average battery life. I send "button state" to central in a timer every 10s, with which I simulate...
Hi,
In my app , using SD130 , when i check the registers state while debuging i find that the RNB is powered on.
Do the SD130 power it on automatically? (because...
Hi All, We would like to use Alert Notification Service and UART service in our application. Here Our Peripheral will be Alert Notification client and UART Service server...
Hi, I have done the following:
Built a custom board with a brand new 128Kb nRF51822. On the board I only have the 16MHz xtal.
Routed out SWD IO/CLK and connected...
Apart from using nRF-Ready mother board, is there an option to program nRF2460. Probably through serial or third party SPI programmer? If yes, which one?
