I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello
I have an problem using I2C on my custom board which uses an Nrf51422 SOC.
I have an RTC chip connected to it and I have no idea how to use your libraries.
The...
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour.
I connect the arduino, ok, open...
Hello everyone,
I have a nRF51822 dev board connected through USB to my PC.
I have connected it to COM5 using Terminal and now I would like to interrogate BLE like we...
Hi guys
I have a custom board with NRF51422QFAA, load "s310_nrf51422_2.0.1_softdevice", program on "nRF51_SDK_7.2.0"
the bootloader I used is "dual_bank_ble_s310"
...
Is there a way to control the max # of packets be transmitted in one connection interval?
(We want to vary it from 1 - 6, knowing that nordic can support up to 6-7.)
Has anyone had any success setting the configuration register on TMP102/112 temperature sensors via I2C? I'd like to switch the sensor to one-shot mode to further minimise...
Hi everyone !
I'm trying to send data from an nrf51822 to an nrf24l01 with arduino and I guess I'm doing something wrong...
For the moment I succeeded to have these talking...
I have a simple ANT beacon application.
UART will be enabled to do some communication. How can I turn it off before ANT goes into sleep mode? Is there a call back function...
I want to send a set of 64 bytes data with ble. as I understand, the max data length I can send within a characteristic is 29 byes. when I send 4 bytes data it works fine...
Is it possible to bit bang a 9600 baud UART on the nRF51822 while the BLE softdevice is running?
The reciprocal of 9600 baud is around 100 µs, so the interrupt handler...
Hi Team,
My application is based on nrf51822 SoC in which I am using
BLE and UART interfaces.
There is single UART available and I have used it in communicating with...
Hello,
I am using am using sd_ble_evt_get and sd_app_evt_wait in an endless loop for handling all incoming events.
If I block this loop from executing, I'd expect that...
Hi all
I'm struggling with the easyDMA UART of nrf52. I've got a preview nrf52-DK here where I wanted to make a simple example with the following code but I never reach...
