I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello, I need repeatitive timer tick of about 10 seconds either in the while loop or as separate callback function. How to create and initialize a long duration tick timer...
Hi,
In Nrf_SK_for_Thread_and_Zigbee, for openthread mtd, we used to define thread configuration in following code:
So to use node as SED (sleepy end device) we would...
Hi guys, I am fairly new to nRF and I try to understand the ways that data can be displayed to the terminal emulator.
So far, I have noticed that there are four different...
Hello there,
I'm starting out on the nordic platform for the first time but I'm running into an issue. When I try to flash the nRF9160 SiP modem firmware with the latest...
Hello
After building the whole environment of Zephyr and the rest, I downloaded the Serial_LTE_Modem build_nrf9160dk_nrf9160_ns example under Segger IDE to nRF9160 (PCA...
We are using public MAC that was purchased from IEEE (20 low bits are available for us to set and the upper 28 bits are constant to value assigned to us by the IEEE).
We...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.8.0 . I'm trying to get the data output (Bus...
Is it possible to override ZEPHYR_BASE when building with the nRF Connect extension in VS code?
I am using workflow 4 (application as manifest repository) and can build...
Hi DevZone.
We have problems with our NRF52833-DK We believe they are damaged because under normal conditions, they normally draw less current (.001 A). It is normal to...
Hello Nordic. I'm using the nRF9160DK and with it, some sensors and an sd-card. I save data to the sd-card using a fatfs filesystem, the files are of magnitude 500 kB. I want...
Is the button (from Thingy52 black case) the only option to trigger an IFTTT? Can I use the sensor's information to trigger an event with the IFTTT? like if the temperature...
Hi,
I am merging a PWM_driver example with a ble-peripheral-blinky example to generate PWM signals with user-defined arbitrary phase-shift and duty cycle.
I am done...
Hello,
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345).
My problem is regarding GPIO configurations are NOT retained ,when the nRF52832...
Dear Support term:
The Restful of Nrf Cloud is not work.
The node should have more that 100 data, so get ListMessages should give us pageNextToken.
Yes the result give...
Hi all,
I am using a custom board with NRF 52840 with SDK15.2 as slave and STM as master. I cannot receive right data, but the data to STM is right.
The above are...
