Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I am developing a product based on a nRF52833-QDAA chip, we use the two uarts to transmit data to another MCU and AT commands to a LTE-M modem.
We use NCS 1.7.0 as...
The nRF connect program for desktop
https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop
Will it be updated to fully support Bluetooth 5? Extended...
Hi,
I got a problem with sending data via gazele protocols, i'm using example library gzll_ack_payload_ host and device, can somebody explain me how this code works?
i...
Hi.
I'm working on macOS Monterey 12.0 beta and trying to start nRF Connect for desktop (version 3.7.0). When i'm trying to start this application it's starting as blank...
Hi.
This question is to confirm again about below.
Is it possible that implement multiple advertising sets, some of them would be 1M and some would be CODED PHY. And...
I'm trying to set up VS code to use it with the NRF Connect SDK. I've created an application from basic/blinky example. My problem is VS code can't resolve any inclusions...
OK, like many people moving across from a different IDE/SOC environment, I'm finding navigating my way through setup and programming with Nordic SOC, even of simple tasks...
I've run into two oddities with the Connected Devices feature of nRF Connect for Visual Studio Code and two different nRF52840 dongles that are connected via a J-Link. In...
Hi,
I try to use zgp api and first try to call zb_zgps_delete_all_zgpd() but I receive an error from linker:
undefined reference to `zb_zgps_delete_all_zgpd'
Is there...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am using openthread protocol...
We want to use GPIO_12 as a wake up pin. (High -> open uart, Low -> close uart) Also, we have a timer and timeout set to 500ms. When we pull GPIO_12 to high, it seems not...
I'm working on NCS 1.6.1 for both nRF52840 and nRF9160.
I'm trying to put my devices into sleep mode so i reviewed some related tickets and found following ways.
NRF_REGULATORS...
Hello,
I am quite new to NCS. I am trying to sending UART data from nRF52dk_52832 to PC.
The example is nrf\samples\peripheral\lpuart.
If I enable the example with CONFIG_LOG...
