Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I had to modify the peripheral blinky example by adding UART module .The program compiles and builds but it is not advertising.I guess there is some problem with the...
Dear All
We implement a DFU over USB functionality to the custom board nrf52840 board by compiling via gcc. Somehow there is my understanding problem with the linker for...
Hi
I wanted to add NUS_C service to multilink central example. I have nRF52-DK (PCA10040) evaluation boards at central and peripheral side. It compiles without errors but...
Hi,
I'm trying out the "Android nRF beacon for Eddystone" app (installed from PlayStore) with the Eddystone Beacon Application example on a PCA10040.
First off, I have...
Hi,
I want to change the bit rate in Mesh light switch example for long range (as of now getting only 15mtrs), i found that there is a function for update phys, but while...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (SDK ver. 12.3.0, SD ver. s130_2.0.1)
Situation is the following:
1. I use peer manager for deal...
I've written a detailed description of how to program & debug the NRF52832 using open-source tools and the Nordic SDK.
See https://iosoft.blog/arm-gcc-lean-nordic-nrf52...
Hi all
I am working on Bluetooth application using NRF52840 kit. The application is very simple, the device would have about 7 push buttons which when pressed data will...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
Hi
I have some questions that need your help.But it seems that there is no answer yet.The following is my questions link.
https://devzone.nordicsemi.com/f/nordic-q-a/52060...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
