Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
Hi,
Having gone through the nRF52832 datasheet, the only discernible drawbacks of moving from an external crystal to synthesizing the Low frequency clock from the high-frequency...
On the Nordic Semiconductor infocenter , 12 reference designs for the nRF52840 are given, 6 for the big QIAA chip and 6 for the small CKAA chip. However the reference designs...
Hi
We are developing the use of ESB together with BLE, using the Timeslot API.
We have been using the known tutorial for the ESB timeslot implementation:
https://devzone...
Hi,
We are using nRF52832(lairdBL652) module for indoor application for the prototype version.
We are using nrf52832 for both central and Beacon device.
We have made...
Hi,
I have combined the light switch and the dimming example. The thingy 52 contains one generic onoff server and two generic level server for brightness and colour.
The...
I updated Thingy91 with modem firmware (mfwnrf9160100.zip) and application firmware (thingy91_ltem_v0.2.2.hex) from latest firmware package (thingy91fwv022.zip).
Question...
Hi,
I have nRF9160 DK. I downloaded nRFConnect SDK with source code.
I know that samples compiled with libraries are loaded and executed under MCU on the DK board. Since...
