Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
use sdk:11.0
Reference routine：ble_nus_c
now I use 52832 to connect a device,the service UUID like the photo.
when I only discover one service UUID,like this code...
I am using an ADC where the SPI MISO pin also acts as a data ready pin when it transitions from Hi-to-Low as detailed in the link below. I am able to configure this and it...
Hi, I am new in Mesh using nRF52840, when I try to build the light_switch example, I link to all the libraries that project need and change the SDK_ROOT to the direction of...
The password I was assigned was 8 characters. I am so sick of these sites requiring logins and passwords that can never be remembered and frankly serving no purpose. I have...
=======
SDK: 15.3
Product all base: ble_app_template
Problem: cannot update iBeacon content dynamically during system run-time.
=======
we try to use ADV with...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
Hardware: nrf52DK PCA10040
nrfutil version 5.2.0
Hi,
I am trying to get the...
We have a custom nrf52832 board. We have nearly 260 boards. After uploading the app through DFU app (nRFConnect) , the new application starts to advertise . The application...
Hi,
We are using NRF52840 in our project.I am using SDK 15.3 and soft device s140 in keil 5 uvision. The NRF52840 Bluetooth will act as central and the other controller...
Hello. I am sending data from the multi-roll BLE module to the central BLE module using Notify. Currently, only the sample project HRValue is sent.
The data related to transmission...
Hello!
I'm using the nRF 52840 module for Zigbee applications. I am implementing a Zigbee router and I need the time-limited commissioning on the device, such as the creation...
Should it be possible to send SMS with the at_client example, and is there any special requirements to do so?
This is the AT commands setup procedure I've used:
AT+CFUN...
Can anybody help me please?
I'm trying to find a chip that will allow me to connect to my smartphone's internet connection over bluetooth.
I don't want to create an app...
I installed nRF connect for desktop in ubuntu 16.04. I added Programmer app . It was working fine till yesterday. But I update it from the nRF connect today. But now programmer...
Hello,
I try to use the opus codec on an 52840-DK. The Build and Flash with ARMGCC woks fine (with gcc-arm-none-eabi-8-2019-q3-update) but I'd like to use the debugger from...
While using the Zigbee OTA examples (nRF Thread and ZigBee SDK v3.1.0), I have noticed by the sniffer, that the attribute “Block Request Delay” is presented in the OTA Upgrade...
