I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
My goal is to capture on gpio burst infrared proprietary "messages" composed of multiple "bits".
The Length of each bit is around 100 to 200us.
Initially I planned...
(I understand my question is similar to devzone.nordicsemi.com/.../ , but I would like some additional clarification not provided in that post.)
Hello, I've been developing...
On a BLE_GAP_EVT_CONNECTED, I'll send some data to an attached microcontroller via UART. The code will expect a response of that data, all while being inside that BLE_GAP_EVT_CONNECTED...
My application involves the Nrf52 using softdevice and a slave only SPI ADC running at approximately 26khz. The ADC has a pin interrupt to indicate data ready. There seems...
Building nrf_delay.c (or anything else including nrf_delay.h ) with NRF52 defined produces:
arm-none-eabi-gcc -I C:\Nordic\nRF5_SDK_11.0.0-2.alpha\components\device -D_DEBUG...
Hi, someone know whi when i press disconnect on iphone the nrf51 restart from the mail?!
Why if i disconnect android device the chip does not restart as the iphone?! is normal...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
I am trying to run BLE central peripheral dual role on nrf52 pca10040 with nrf_uart as service. Also, I have redbearlab BLE nano as peripheral (nrf51822 based).
I am getting...
