Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
So, I am working on nrf52840 with nrf connect sdk and I want to get date and time in my project, I found a library in nrf connect sdk ->libraries->other libraries->date-time...
NCS 2.7.0 Zephyr 3.6.99
I have &uart1 described with status = "okay"
With a sub node of gnssdev: gnss-nmea-generic also with status = "okay"
I have tried with both pointing...
Hi, In one of the previous ticket (link: ), there is a link about an example to create an application with USB CDC/ACM and MSC at the same time. The link is no longer valid...
I am writing software for a battery-powered device that needs to go into the lowest power possible sleep mode when not in use and be able to wake up with one of 8 buttons...
Hello,
I've been trying to get the nRF Desktop Dongle/HID Forwarder to work, ie. I program a nrf52840DK as a HID forwarder, it connects to my bluetooth keyboard, and then...
Hey Team,
While connecting the battery to the nRF5340 Audio DK, we have observed that it only charges the batteries with 3 pin connector is being charged. However when we...
Hi, I just want to read accel and gyro data from the on-board BMI270 IMU on the Thingy 53. I'm using the sample code from zephyr and I've modified the dts and overlay file...
my chip is nrf52833. In guide document , the XC1 and XC2 would connect to capacity. Both pin is used.
My project need one pin TCXO. which pin I should connect to? XC1 or...
Hi, everyone.
I am testing reading/writing data between n52840 and n9160 through UART with buf_len=1(byte by byte) based on Zephyr's UART_ASYNC_API provided in ncs v2.6...
I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add:
& uicr {
nfct...
Hi ,
In NCS 2.8.0 the ESB-PTX sample how to config to achieve?
Now I had disable the UART log,after transmit 20 seconds I want to config the nRF54L15 into a low power...
There are 2 software: 1.0.1 and 1.0.2. When I load the 1.0.1 hex with bootloader with the programmer, it draws 9uA current. But when I update it to 1.0.2 with DFU, the current...
We are flashing the nRF52832 that works with DFU with a SoftDevice and a bootloader. The application code is compiled privately with a private key and packaged into a zip...
