Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
When using SDK 2.6.x, I didn't know about Wi-Fi Credentials, so I connected to Wi-Fi as follows:
(Partially omitted)
With the release of SDK 3.1.1, I learned about Wi...
Hello, As part of an effort to migrate applications to nRF5415 devices, I've encountered voltage sensitivity issues when using existing sensors (bme688, bme280). After reviewing...
We have designed two custom boards based on the nRF52840.
Board #1 (Demo board) This board works correctly. It uses a standard 32.768 kHz passive crystal connected to XL1...
Is it possible to enable the Segger Flasher ARM Targer power supply using nRFutil?
We are now using a Segger Relay adapter , but this needs the Flasher's ARM target supply...
Looking for base examples for a push to talk using this dongle board and GATT. I choosed Peripheral LBS
Other basic example (Beacon, Blinky etc) compiled and work w/o problems...
Hi,
We want to set the PMIC's battery discharge limit via the registers BCHISETDISCHARGEMSB and BCHISETDISCHARGELSB to 1200mA but the nPM1300 PS does not describe how to...
Hi!
We're assessing the EN18031 compliance, and would like to know if there's any plans for product certification with nRF9151?
I found that the certification was...
Hi, I was checking the HAL for SPI in master mode and notice that when pm_device_action_run(<spi_device>, PM_DEVICE_ACTION_SUSPEND); the CS pin isnt changed since it status...
I want to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.2.0, to hopefully get the wifi WPA Enterprise functionality to work. This is an existing...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following error message:
fatal error: nrf.h: No such file or directory
"nrf.h" is now located...
Hello, I'm using Nordic Central HR example. I'm wondering how to read RSSI of a BLE device connected to the NRF5340, I have tried multiple version found on this forum, but...
Howdy,
I am trying to connect a Waveshare BME280 to my nrf9160dk, and it's not obvious which jumper goes where. The documentation states:
Wire color
Sensor board...
hi,
i'm new with the nrf9160DK so can you please guide me to how can i start and config my nrf9160Dk with my laptop from scratch because this video is not helping me https...
