I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi, I am using a module named MS12SF1 (nrf5340 + nrf7002). I was trying to write the Mac address for one time programming by using radio_test sample code. Before doing this...
Hi devzone, I am trying to use the Edge Impulse integration on a Seeed Studio Xiao BLE Sense (nrf52840 based). When I manually download the zip file from Edge Impulse and...
Hi,
I have a project which has been working fine but since adding some date/time functionality, when I enable MCU_BOOT, I get linker errors that I can't seem to get to the...
Hi all,
I'm developing a multilink system with 52840 dongle as central and 8 52832 devices as peripherals, which is similar to previous project in thread part I & Part II...
Hello,
As mentioned in the title, I am trying to use 4 pairs of I2C on nRF5340. Each of the four I2C pairs will be connected to a TCA9548A (I2C MUX), but that is not important...
I want to try out remote mesh provisioning.
I have added a mesh device with Remote Provisioning Server model to my mesh network with nRF Mesh app as the provisioner.
But...
Hello,
I've been trying to setup the nRF connect & power profiler on some of my co-worker, but downloading the pc-nrfconnect addon was not possible via nRF connect, so I...
i used my j-link to flash to my thingy91 nrf52 and nrf91.
now i want to flash a new program using the usb, but nrf programmer doesnt recognize a device when i use a USB...
Hi, I'm trying to send 64-byte reports for INPUT and OUTPUT: 1 byte for report ID and 63 bytes of data. However, the HID service code doesn't seem to handle incoming OUTPUT...
Getting error: board.h and other header no such file or directory. with nRF5_SDK_15.0.0_a53641a and nrf5sdkformeshv500src in the same path.
What could it be?
The evaluation...
I'm writing my own lightweight bootloader for nRF5340 (which may or may not turn out to be a good idea). I have something similar that I'm using successfully on nRF52832 based...
When I use the command to read the software version, the message read by the Raspberry Pi does not appear " SoftwareVersion ".
Please confirm the attached LOG message
Hello,
I have a question about performing OTA via BLE (SMP) and using BLE mesh. Is it possible to perform OTA via BLE to ZigBee network and vice versa.
Since BLE is supported...
Hello,
I'm encountering issues while trying to install and update the nRF Connect SDK (NCS) environment on my macOS system.
NCS versions attempted: 2.2.0, 2.6.1
...
I am using nrf52840 to test the `periodic_adv_rsp` sample application using ncs. I had this use case where I would like to configure data in a subevent based on responses...
