Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
Hi,
For the first time iOS App interface with BLE device. But after killing and re-opening of iOS App connection not established. Can anyone share me the code from iOS App...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
Dear, I have bought the nRF5340 DK. I have installed nRFConnector and Segger Studio. Now, I want to test Blinky project. I connected a USB cabel to USB connector which is...
I have a receiver , transmitter application. I use a custom board as transmitter. I would like to use pca10040 as receiver but currently i use it as debugger to my custom...
Hi,
Our company has produced a batch of BLE products, and the 10uH inductor model used above is SDFL2012S100KTF. The rated current is not as large as the current value...
Hi,
I close the uart log and open the rtt log
why uart log can be used still?
why rtt log display error state?
I set the log config like this:
I set the test...
hi
i have this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_timer_cnt_get (referred from max30105.o).
in this code part.
the example is...
I have a program that runs great on the dev kit, however after uploading the code to a custom board based on the nRF52810, it does not seem to run.
I upload the code by...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
