Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I changed the I2C pins to below, and it not work. so is it possible to reconfigure the I2C pin? what should I do since I already set to 8&9 in the hardware board? const nrf_drv_twi_config_t...
Hi,
Looking for some ground on getting the netowork parameters set for a zigbee device, My intention is to limit the number of scan intervals and the scan time to save power...
I'm planning wireless conference system. This needs some condition as under simultaneously use 5ch of wireless bi-directional connection through whole system. Each wireless...
Hi,
I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file
I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.
how...
I am trying to update firmware that uses v14 of the nRF5 SDK to firmware that uses v15.3, but I am getting the error "Init command larger than expected.".
I'm wondering...
Hello everyone,
I'm running the IoT CoAP example on my nrf52840 Development Kit.
The border router is Rapberry 3 B+ on Jessie with Kernel version 4.19.46. I've put BLE_6LOWPAN_LEGACY_MODE...
I am using nRF5SDKforThreadandZigbeev300d310e7 sdk for thread example simple_coap_client. I try to add uart module with simple_coap_client and i have added uart configuration...
Hi,
I am running nrf52840 on a custom board, SDK 15.0.0, softdevice S140 6.0.0 and SES.
In my application I am reading an IMU ( ICM20602) and a laser ranger/Time of Flight...
hi,master.
Question 1: In Asia, the speed of accessing web pages is slow. SDK15 development documents can only be accessed online on the official website, but often cannot...
Hi,
I am running NRF52840 on a custom board with SDK 15.0.0, Softdevice S140 6.0.0 and SES.
I am measuring using a toggled GPIO pin measured on a CRO. This produces a...
I'm using an nRF52DK to monitor the RSSI and MAC address of my two phones through ble_evt_handler BLE_GAP_EVT_SCAN_REQ_REPORT.
I tested both Android and iPhone. They both...
Hi all!
I have small problem. When I build my project, it returns thise error: Symbol SWI2_IRQHandler multiply defined (by nrf_sdh.o and nrf_drv_swi.o). I want to use SWI0...
