I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello ! I have an issue that is making me crazy so far
I am trying to connect to NRF52832 devices with my smartphone. They have to collect data from sensors inside smart...
Greetings,
I'm getting some trouble trying to fix a warning. I'm running the exemple ble_app_uart_c from the folder ble_central. When I run it, I keep getting the warning...
Hi,
From the pwm driver, there is a function that use sequence that control the dimming while not blocking other task in the program, may i ask if there are any function...
Hi,
is it possible to use the GPIOTE in OpenDrain mode?
I want to use the Timer with an GPIO. So i use GPIOTE with PPI connected to the Timer. This works. But my Pin Configuration...
Dear Nordic Team,
I am trying to use the MWU to safeguard RAM of my application. Since softdevice also use this unit, I wanted to understand that where I can write the...
Hi!
I can able to read values from BMP180 but I am getting random values.It shows temperature values in some 200 range like that.How to get proper temperature value??? ...
board: custom board nrf52840
IDE: keil5
SoftDevices: s140 V6.0.0
SDK: 15.0.0
hi, I want to decrease my consumption of my board.
Now, i enable the SoftDevices and...
When I am using peripheral/cli example and debugging through RRT, I see following outcome when I am typing commands.
OUTPUT :
Command Line Interface example started...
Hi,
I am working on light switch example. I am broadcasting a message from client to servers using the API access_model_publish() with the opcode SIMPLE_ON_OFF_OPCODE_SET_UNRELIABLE...
Hi:
When I tested the DFU function of BLE, the upgrade was unsuccessful, and the APP print log prompt appeared to be a CRC check error.
The SDK version I am using is nRF5_SDK_15...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
Hi ! I have attached the PCB design and schematic provided by Nordic for nrf52832 which is said that its also same for nrf52810.
I wanted to use the nrf52810 board for beacon...
