I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
We are evaluating the nRF54LM20B for an embedded audio classification application and are trying to determine whether the Axon NPU can meet our latency and energy targets...
Hello,
I encountered an issue when using BT_LE_ADV_OPT_CODED in the bt_le_adv_param options.
When I enable BT_LE_ADV_OPT_CODED , the device cannot be scanned by other...
I am currently developing a project using an nRF5340DK and a custom board. ---------------------------------------------
PC ---(SWD)--- IntMCU at nRF5340DK ---(SWD)--- nRF5340...
Hi,
We are trying to get an accurate estimation of energy consumption of LTE searches and data sessions.
We currently do this based on XMODEMSLEEP and CSCON notifications...
I'm a bit confused about configuration necessary for PAwR where a connection is initiated with AUX_CONNECT_REQ as in examples periodic_adv_conn/periodic_sync_conn. If I disable...
Hi, I’m seeing a build failure after enabling SQSPI in the device tree when building with MCUBoot on NCS v3.2.1 for nRF54L15. The build works fine without SQSPI, but once...
Hello,
Did anyone get nrf54L15 to work with a TFT display over SPI?
I have been using the 1.28" 240x240 gc9a01 in several projects with nrf52840 (both using the DK...
Hello,
Recently I designed a wireless keyboard with a nRF52840 as the main processor. I had the board reviewed by a friend and had it produced by JLCPCB. I have assembled...
I'm currently attempting to profile a non-rechargeable lithium battery on nPM PowerUP(2.2.3). When I start the profiling process, the charging stage is correctly skipped,...
We've designed our own board based on nRF9160 for main CPU w/ LTE and an nRF52 for BLE. Using BMP for debugging.
I've successfully run several boards through the production...
hi,
i'm learning this exercise and i got this build error.
i'm using nrf 9160dk so can anyone tell me what problem am i facing in build time error.
thanks
vivek
Not sure if this is an nRF Connect or VS Code or Zephyr or West or some combination of the above, but I'd like to configure the development environment (nRF Connect extension...
Hello Nordic,
I am currently evaluating the nPM2100 using the nPM2100 Evaluation Kit for a low-power embedded device powered by a CR123A primary lithium battery (Li-MnO...
Hi,
I am testing an eSIM card. I am able to read the ICCID (20 digits) using the following command:
AT%XICCID %XICCID: 8934014012215261620 OK
However, I don’t know how...
