This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi, everyone,
I am pretty new to nRF52 development. Right now, I have an issue with the SAADC trigger by RTC, which I follow this example . The issue that I have right now...
Hey all,
Here's another question. Many of the examples in the Nordic Connect SDK are rather large. Transferring them with MCUmgr at 115200 BAUD takes sometimes more than...
Hi
I am testing sending and receiving data between nRF51 dongle and peripheral by example of heart-rate-collector.
now I could find characteristics I need(write, read...
Hi all,
My application is as follows:
I have an android app which will send some data to a nRF DK. The data I want to send is in HEX characters between 0x00 to 0xFF. And...
Hello,
For nRF51822 and nRF52832, I'm using GPIOTE, PPI and timers to measure the duration that a pin, which is normally low, goes hi (typically 100-300 milliseconds). I...
The following questions are in regards to the instructions at nRF_Connect_SDK-modifying-a-sample-application .
In the Windows environment, I am transitioning from using...
Dear all,
I recently made a custom PCB using the aQFN73 package of the nRF52840 and, even though I respected the antenna constraints (but in 2 layers) I get no signal whatsoever...
Hi Devzone:
I am using P0.00 as SDA and P0.01 as SCL on nRF52833, And I got waveforms like below when I am doing I2C transactions:
the red waveform is SDA and the green...
Hello,
I slightly modified examples\multiprotocol\experimental\ble_zigbee_dynamic_color_light_bulb_thingy so that it can receive changes in the color temperature attribute...
currently i am doing my master Thesis in Bluetooth low Energy. I am searching for BLE Transceiver for Evaluation Purpose. I have a development board S32 from NXP and would...
Hi,
I want to create a Thread border router and am following the instructions from the infocenter.
In the hardware requirements, it is mentioned that the image needs...
Hi Team,
We are using the nrf52830 SOC for our application. In data sheet mentioned that it supports AES-128 bit Hardware engines (ECB,CCM, AAR). How to enable and use these...
Hi guys
I am trying to load a firmware to a Minew's nrf51822 Module using a JLink V8 programmer tool. So far , I can see the chip with the Jlink console:
sudo JLinkExe...
Hi all,
We had implemented Nordic QSPI using "nrf_drv_qspi_write" and "nrf_drv_qspi_read" operation , however I am seeing for page to write in flash of 4096 bytes with 512...
Hi,
During our development, we observed that when BLE central and peripheral devices are communicating, then often central device will not receive data from peripheral device...
