The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi there,
I found very interesting behavior on casting double variables to integer.
The following code gives me strange result:
double dval = 0.;
int ival = (int...
Hey,
Currently I have been working on a project in which I have to calibrate the range of the bluetooth, basically I need very short range of about a meter.
Could anyone...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
Hi,
The device I am using is nRF52840, WLCSP package. Most of the analog IN pins are noted "low frequency I/O only", e.g. pins A5, A6, C7, C8. - I know there are some exceptions...
Hi,
As of now we are using SEGGER Embedded Studio for compilation and Flashing.
Now we would like to copile using Cmake tool, can you please provide template Cmake for...
downloaded thingysdkv210 from thingy website. extracted that file and executed Prerequisites as per the procedure
downloaded Python v3.xx.xx
downloaded Git v2.xx.xx
...
Hi,
I am trying to add CLI Command feature into the example Open_bootloader_usb_mbr, but get error during link stage when compile as below,
Building ‘open_bootloader_usb_mbr_pca10059_debug...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am using multiple interrupts. For example, BLE communication interrupt and SOC interrupt. I set the priority of each interrupt...
Dear Sir,
I have flashed 'ble_app_hrs' code to one of my RIGADO DK.
I have installed nRFConnect App in mobile phone.
When I press the scan button I could see the device...
Ok I am using GPIO interrupt and want absolute power saving but when I set the GPIO_INTERRUPT_HIGH_ACCURACY to true it works fine but when I set GPIO_INTERRUPT_HIGH_ACCURACY...
Hello,
I want to use P0.27 as output but no way to get it working (tested on my custom board and on DK). If I just change for another pin to check my code, it's OK.
It...
Hi,
I am using nRF SDK v16 with nRF52DK (pca10040) development board.
I've chosen to use RTT logging and I can see my app logs in JLinkRTTViewer window --- however, I...
Hello!
I am developing a FreeRTOS application for nrf52832 with S132 Soft device
Recently I ran out of ram and checked the map-file for clues. The large posts in the mapfile...
Hi,
I don't understand why the characteristic FitnessMachine Feature : (0x2ACC) is not decoded as a bit field by nRF Connect
I can read it and i can see the good value...
