Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
I'm using nRF Connect v3.0.0 to run Getting Started Assistant v0.9.3 and get a message it is only compatible with 2.4.0 (very old). I can install and verify Tool Chain except...
Hi
I am trying to connect and bond a nrf52832 to Galaxy S6, Android 7.0 by OOB / NFC with the ble_nfc_pairing_reference_pca10040_s132 example.
I selected LE Secure Connections...
Hi nordic,we want to config nrf52832 as a wireless full-duplex serial port transmission module through nordic proprietary protocol，so the module can send and receive data...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
Hello,
I have problems setting the output RF power to +8 dBm during DTM test using the example dtm application. The example dtm application is used as it is provided with...
Hello,
i've been searching the forum for answers about Bluetooth certification but i'm very confused.
I want to use nRF52832 in my project, and i would like to make make...
I am trying to transferAdvertisement data from NRF52832 to Raspberry PI using BLE_app_UART example. I have updated the config as below,
app_uart_comm_params_t const comm_params...
Hi,
So this may seem like a stupid question but here goes. I've been trying to learn how to implement an IoT solution.
While trying to learn more about MQTT protocol...
Hi,
I'm trying to build the example found here: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
and the build is failing with this...
Hi!
I've been trying to connect the nRf9160 to an AWS IoT account following the directions here https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples...
Hey guys I am using nrf52840 dongle for scanning ble beacons. I want my dongle to be power optimized in a way that it starts scanning for 10 sec and then go to sleep for one...
Hi,
I am working on nRF52DK. The Bluetooth MAC address is stored into the Flash during the pairing sequence. Can some one provide me the links to understand the storing...
hello
hi
I connect AT24C02 EEPROM with nrf52dk.
I connect SCL to 27 pin ,and SDA to 26 pin.
I open twi_master_with_twis_slave sample code and make some changes(i2c...
Hello there;
We want to develop a project using the nrf52 series. We have two nrf52s. The first one is in the center and connected to the mains and there is no battery problem...
