Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
what is the problem of "ERROR Failed to open nrfjprog: Error occured when open device long term. Errorcode: CouldNotLoadDLL (0x3)" , when i use the nRF Connect.
the version...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
