Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
nrf51822QfAC
S130 stack was working fine and ble_app was able run successfuly able to see the ble on the app;
Now after few days now facing issue in running the same code...
having issue with nrf51822
nrf51822 breakup board was running fine with S130 2.0 stack and ble_app_uart
Now facing issue such that when softdevice enabled is called the...
Hi,
I just switch to Embbeded Studio following the last tutorial ( here ).
I'm working on NRF51822 with SDK12 and TWI_sensor example (without SoftDevice). I followed...
I see from the release notes of s132 4.0.0-2.alpha that it adds:
Support for 20 links in total with freely selectable role (Central/Peripheral) for each link.
I want...
Hey,
I am trying to control an external LED using two nRF52832 boards. I am using "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\experimental_ble_app_blinky" code for...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
Hi,
I have searched for examples which will use passkey to connect with android, but didnt find any.
I want ble_app_hrs example to connect with nRFConnect in android by...
HI，i develop my project base on “examples\ble_peripheral\ble_app_uart” and “nRF UART v2.0”。i hava large data transmit from phone（androd） to nrf52832。
but when send a package...
