hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi, I am trying to use P0.9(nfc pin) as gpio(input) to read the charging status of a battery from battery charger IC(BQ 24230). the Open-Drain Charging Status Indication of...
hi Nordic engineer
hard platform : N53832DK, 51822DK
software platform nRF52832 use SDK_14.2.0, nRF51822 use SDK 12.3.0
nRF52832 as ecntral and peripheral; nRF51822...
Greetings,
in the system I develop I shall have a task resposible for fetching some amount of data from Flash to RAM. I should mention that the code will be executed from...
Hi,
I try to activate the bonding with the "ble_app_multiperipheral" exemple project I have modified.
It is very strange because I can bond as wanted but only if I set...
Hi all,
I am having query regarding BLE Security.
Which options are provided by BLE for security.
Can anyone provide option in below category?
1. Security in Connection...
Hi all,
Going through the sniffer document and devzone tickets, I observe that there is no official nRF sniffer software to emulate nRF52840 QIAACA SoC as BLE sniffer. ...
Hi Everyone
I was trying to use segger embedded studio for nrf52840 PDK.
I could get the example codes working but when i tried to create a new project and try to include...
Hello, I am trying to initialize the service Power Cycling from the files of this link https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
I get...
Hi,
I've been trying to use the nordic power profiler v1.1 with my nRF52 development board to figure out how much current is consumed during operation.
I used the power...
In the light-switch-proxy-client example there is every unreliable group message repeated a number of times (GROUP_MSG_REPEAT_COUNT). Is this always required to be implemented...
When the nRF53832 is connected with a cell phone for data transfer, can it still be discoverable, and go though pairing/bonding process with another cell phone? I think the...
Hi, Just porting an old project from nrf52832 to a nrf52810. I've had trouble finding a bare-bones project (arg-gcc), basically just main + log for the 52810.
I understand...
I have four Bluetooth modules (servers) that measure pressure continuously. The servers should connect to the client and send the measurement data to the client. I can read...
Good afternoon,
We are developing a consumer product that is using the nRF8001 as the BT peripheral. We have a question regarding certification; do we need to undergo...
