Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Hi
sd_ble_gattc_primary_services_discover() is being called from ble_db_discovery_start() within ble_db_discovery.c. I'm trying to get the ble_cts_c service working. It...
Hi
I am receiving INVALID_STATE (error code 8) from ble_db_discovery_start. According to documentation, this error can be returned "If this function is called without calling...
Hi, i have just bought a NRF51 DK. I have tried to run the precompiled Blinky example. I have first installed NRFGo Studio. I connected the board. In NRFGo Studio, I selected...
Hello,
I am making a battery service to report the battery that is sampled by the SAADC, so far I am am able to compile it and debug it, however I see how my saadc_event_handler_interrupt...
Hi
I'm reading the debug output of ble_cts_c.c:
NRF_LOG_DEBUG("BLE event handler called with event 0x%x\r\n", p_ble_evt->header.evt_id);
However I can't find any...
The analog circuits 51822 and rfx2411n supplied by the authorities are connected 52832, but the circuit is not working properly.PA and LNA switching has been controlled in...
This is to build upon a previous question i had here .
This time, I am having issues with SDK 14.
I can compile and run the BLE peripheral HRS example fine. With SDK 14...
Hi,
I am trying to write 64 bytes to a characteristic as a client and am getting the error NRF_ERROR_DATA_SIZE . The infocenter is not very helpful at indicating where...
I am using S132V3 on NRF52832 device. In my application we need to set a static, non-rotating, private resolvable address. I can't get into why that is here. In theory this...
Hi all,
I'm using chip nrf52832 with the last enabled stack which integrates the adaptive upgrade for bluetooth 5.0. However I'm insterested in long range and that's upgrade...
Hello,
Is there any example of simple peripheral to update the firmware using over the air download for nrf51?
waiting for your kind rhelp.
Regards
MAbbas
Recently,I confronted some particular circumstance that I have never came across.
The device programmed used by Jlink and Keil,so I check the address of flash,it showed as...
hi all,
i'm using nrf905 for wireless communication at range of about 30meter @433mhz.
and have some question ,maybe your guys can help me.
thank you.
q1:upclk pin...
According to the documentation, it is possible to upgrade the Thingy:52 firmware via a cable connection using nRFgo Studio. Can I connect the Thingy:52 directly to my PC?...
