Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
In the sensor datasheet it says one can use SPI_Mode 0 or 3 (doesn't say that there is anything to do to switch between them).
I connected MISO from the DK with SDO from...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
I'm trying to minimize current consumption on my BLE peripheral and I wanted to know what advertising data is required. I have a custom service with a 128-bit UUID but do...
Hello!
I am using a keyboard (4x3) and the rows are configured as input PD and columns as output set, after a successful interrupt , the columns and the rows shift settings...
I am using nRF8001 bluetooth ble for my project. I would like to get the RSSI value as a reference value in my firmware. Is there any way that I can get the RSSI value from...
Hello,
I'm using the following (nRF51822-Beacon): www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit
I would like to use the beacon for beacon-to-becaon and...
I am calling the spi_master_send_recv in a ISR from a GPIO using app_gpiote.c It causes a hardfault on APP_ERROR_CHECK(sd_nvic_DisableIRQ(p_spi_instance->irq_type)); Otherswise...
