Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs
but:
1.How does the client receive those data?
2.How dose the client send data to server...
I'm totally new to Nordic, ARM development, and the mbed platform. Not new to embedded development however.
So far I can't get the simplest possible program to run.
...
I just received my nrf51822 dev kit and noticed that the SWD debugging cable will only connect to the PCA10004. The PCA10005 that came with my kit has pin 2 missing, rather...
HI,
I wrote my application based on "MasterEmulator->ProximityDemo" for testing device with nrf51822. My device have to switching between Gazell and BLE stacks so all the...
Hi
In ble uart project, the data is used string format. Now, we want to modify uart apps to tx/rx binary format. Could you tell us how to modify the uart apps? Thanks.
...
I added a local service with a characteristic with the Notify permission set.
On the device I'm connecting from to the nRF8001, I can see my custom characteristic has a 0x2902...
I'm designing what is essentially a small beacon board built around an nRF51822. On the antenna outputs I've used the discrete component balanced to unbalanced circuit shows...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
