I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
I modified the BLE fundamentals lesson 5 exercise 2 example ( github repo ) for my purposes. This uses a generated passkey for pairing with accept lists.
I removed the...
I've had success getting the Sigurd Hellesvik Serial Recovery sample to work on an nRF52840 DK with mcumgr cli commands. I'm able to flash the Fanstel 840 with the same bootloader...
How do I resolve/update:
zephyr-sdk is outdated. Found 0.16.5, but 0.16.8 is required by the SDK.
python is outdated. Found 3.9.13, but 3.12.4 is required by the...
Dear Nordic Support Team,
I am encountering a persistent error while setting up NRF Connect for Visual Studio Code. Despite numerous troubleshooting efforts, I have been...
Hello,
I want to use the PPK II in a free-running state in Scope mode, which is the same behavior that most oscilloscopes refer to as Auto triggering, but it appears that...
Hi!
I am using direction_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA.
RX board: nrf5340 devkit + antenna
TX board: nrf5340/nrf52833 devkit
Problem...
I didn't see an issue tab on the Github page for sdk-nrf, so I'm proposing this here.
My device acts as both a central and peripheral, but as a central role I am connecting...
Hello,
I am using the nrf21540 with the shield nrf21540ek; nRF Connect SDK 2.6.2 and the toolchain 2.7.0.
Currently I am getting the following warning on the log output...
Hello,
I am using nRF Connect SDK v2.6.1 and nRF Connect for desktop v5.0.2.
I am currently developing with the nRF21540 and for some tests, I want to use the RSSI Viewer...
I am currently working on a project using an nRF52840 with an nRF Mesh controller and have run into an issue when trying to perform Device Firmware Updates (DFU) using multiple...
I'm developing a BLE application on nRF52840, where several characteristics correspond to several parameters. I need to read and validate parameters stored in flash when the...
Hi
We are using the nRF52832 with the SoftDevice S132 V7.2.0. Recently, we had to enable the FPU whereby we have to re-evaluate the consequences of erratum 220.
According...
Hello,
This is a theoretical question rather than a problem:
Let's say I have 2 devices that need to communicate over standard BLE profile and every so often needs to...
I'm using SDK1.3 on a nRF52840 and running BLE on it. I'm using FreeRTOS under it and specifically non-preemptive scheduling. From time to time I do a scan using a filter...
After upgrading to NCS 2.7.0 I noticed the MX25R1635F (A very commonly used / well supported chip for zephyr) no longer enters deep power down. On further investigation, changes...
