I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
HI NORDIC, I met a problem that Bootloader coulde jump to application, and the application crashed with freertos and softdevice SDK13.0. However the application could run...
After reprogramming with mfw_nrf9160_1.2.0 and nrf9160dk_asset_tracker_ltem_2020-04-29_bc7ade8b.hex
the nRF9160 fails to connect properly. LED3 blinks continually, LED4...
Hello,
currently i am using nRF52832 board with Nordic SDK 16.0.0 and softdevice version 7.0.1
i have separated DFU service and bootloader code. added dfu service in my...
Hello all,
I'm still learning C at this point of stage. What I ended up was following a tutorial online on simple BLE project controlling the on-board LED.
The tutorial...
This is a 2 part question concerning the LFCLK input levels as well as how to test the LFCLK frequency against the HFCLK frequency to make sure they are consistent.
In this...
I am currently working on a project using the MAX30102 Heart rate module. This sensor has red & ir led's. I connected the the max30102 sensor to the nrf52 DK as follows VDD...
Hi,
I'm looking at the BLE aggregator example, it uses a service called "ble_agg_cfg_service" .
1. It looks like this service is the same as NUS ?
2. I'd like to...
Hi
I am evaluating the production of a BLE product and your chip solution looks promising.
In my case the bluetooth will be connected to PC and it should be recognized...
There are a number of issues in ble_advertising that relate to changing the status of advertising in response to events. Specifically the current adv mode is not changed on...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
