I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi,
we are using MQTT to push the sensor and GPS data with 1 hour interval. After 4 consecutive connect and disconnect, MQTT is returning socket error. It requires the device...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service with the SIG's PTS device (dongle)
So far encountered a problem with Test Case: BAS/SR/DES...
Just got a nRF5340 DK, testing on macOS 10.15.2. Setup was smooth – the nRF Connect assistant is pretty good. The only feedback would be that an explanation of the "Variables...
Hello Nordic Team,
I'm currently working on a project based on the nRFready desktop. My application requires using the pipes 0-2: pipes 0 and 1 are used in conjunction with...
Hello everyone!
I want to use the app_sdcard to read/write with fatfs on a uSD card in my app which is based on FreeRTOS. While i was implementing this library, i saw that...
Hi,
I would like to know, where the packets are written into the flash for the mesh DFU example.
In nrf_mesh_dfu.c is a function nrf_mesh_dfu_cmd_send:
It calls...
Hello,
I have a little issue during the mesh configuration of my network.
First my provisioner (called master) provision and configure a first node (called slave), this...
I have downloaded project from https://devzone.nordicsemi.com/f/nordic-q-a/55710/while-building-thingysdkv210-on-segger-showing-error-thingysdkv210-source-modules-thingee_ble_handler...
I am using Nordic's nRF52840 DK board.
I wanted to sync time on End Device(nrf52840DK Board) via sending packets to it. What should I do?
what clock/rtc library or API...
I am sorry but this is totally BS. I just got the Thingy 91 and it does only problems...
I have no problem using a full day on getting stuff like that to work, but please...
I am currently developing a device and would like the default behavior at boot to be:
1. Boot up
2. The device should start advertising for non-bonded devices.
3. When...
Using the 15.3 SDK and the 6.1 software device I am successfully changing the transmit power as needed. When not connected and advertising I would like to update the advertised...
hi
i have a problem with 51822.
i test my production, power on /power off again and again.
maybe 51822 can not work. but is too hard happen.
My code is at main output...
