I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi
I would like to connect a BME680 sensor to the nRF9160DK board. The driver for this sensor isn't included included in the v1.14.99-ncs2 branch but it shows up in the...
Hi,
I want to directly enable notify without discovering the service handle, but it didn't work(return NRF_ERROR_BUSY). Because it takes time to discover the service, and...
Hi, As we know that, we can see, the data has been sent to nRF Cloud in JSON format by Thingy91-PCA20035. And we can also see that, we have respective APIs like "cloud_send...
Hey,
I am getting a
warning: #47-D: incompatible redefinition of macro "STATIC_ASSERT_SIMPLE" (declared at line 215) warning: #47-D: incompatible redefinition of macro...
Hello, I am working on a ble application which is streaming data via ble notifications. I am currently queuing up the packets in the notification queue and keeping track of...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
Hello, Nordic.
I'm currently developing multiple sensor beacons and a scanner for asset tracking (scanner app based on ble_app_uart_c)
ble_app_uart_c has SCAN...
Hello,
Im designing a board with nRF52832 with acceleration sensor and BLE application, so for the esd protection, should there be an housing of some sort, what all can...
We're migrating from Zentri AMS002 chip to to nRF52840.
We use custom service UUID: "175f8f23-a570-49bd-9627-815a6a27de2a" in nRF firmware.
As attached images show, custom...
Hi!
We're developing a board where we would like to switch between normal power mode (VDD shorted with VDDH) and high power mode (VDDH as input and VDD in highZ or supplying...
