Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
Hi, I am now studying on the basis of advertising tutorial example.
When I connect to the device, I want to turn on the led4 in the main loop(To just study), but I don't...
We need a simple program that can be used as a terminal program on Windows (with nRF52840 dongle attached) to a remote device running the BLE UART service.
Essentially,...
I would like some guidance on how to start a project using the nRf52840 - i.e., what sample programs would I start with? The project is a remote control lighting application...
I used the example pin_change_int from peripheral examples and commented the OUT pins. In addition I added the sleep commands to the main while loop. This is the code:
...
Hello everyone,
I'm currently working on a project that requires a nrf52832 chip to relay raw beacon data over UART to an esp-12F module. I am having a difficult time figuring...
Hi.
I have NRF52 DK.
I have successfully flashed TWI sensor example on to the board.
However, when I move forward with other projects in SDK like ble_app_uart and ble_app_blinky...
Hi I wanted to ask if there is a driver/library for the mcp25625 chip? Also for the communication do I use " SPIM — Serial peripheral interface master with EasyDMA " or "...
I'am achieving lowest power consumption in connected mode. I can't identify source of short spikes every 40Hz when mcu is in low power mode. I'am sure that it's not application...
under code is my sdk main code and i want to change code to Sensor --I2C-- nRF52 --UART-- app but where i have to start and change ?
/* Copyright (c) 2010 - 2017, Nordic...
I've been doing some testing with Mesh DFU and I've noticed some unexpected behavior around handling missing data segments.
As I understand the Mesh DFU protocol, if a data...
I have issue about calibartion using saadc.
I use 52832, S332, SDK 15.3.0
when calibration is excuting, ANT+ and BLE is also doing.
I use low power mode in saadc.
...
Hi
I want to know if there is any source code of thingy91.
Because I want to follow thingy91 for making a product with the use of the same antenna, and I want to know...
Hi,
Recently, I was trying to move my project from STM to Nordic IC.
I just wonder how to implement the below codes into the nRF52832 or how to program it in Nordic environment...
Hi,
I want to set sending power(+4dBm) of NRF52810/NRF52832 with SDK 15.0.
Now,i find i should use the order of sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle,...
Using a AF_INET UDP socket on the nrf9160 I will get ENOMEM when I send a bunch of datagrams over the socket. I understand how there can be a limited number of buffers for...