Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Since the manual for the nRF9160 DK doesn't have a full schematic, I'm not sure what sort of power supply decoupling the nRF9160 needs. What are recommended bypass caps, if...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...
Hi,
Is there a tutorial or guidelines on how to send ble-app_hts data to nrfcloud mentioned in this Noridc video below.
Nordic Semiconductor - nRF Connect for Cloud (youtube...
We have an implementation where we need to limit data, and to be able to KNOW how much is actually being sent with the operator, to limit costs.
In a normal Ethernet condition...
Hi Nordic,
I am trying an application where both central and peripheral devices are based on nRF52.
I have to create custom services and characteristics for the same....
Hi, I am beginner for nRF51822. We are using SDK v10 and S120.
We have an IOT Gateway with it's processor interfaced with nRF51822 radio through UART. We have flashed nRF51822...
Hi all, We always have -4Mhz Radio Frequency Interference when using nrf24l01 and nrf52832 chips.We use nrf24l01 as a slave receiver, and use nrf24l01 or nrf52832 as a master...
Hello,
I'm trying to set up my nrf9160 Dev Kit and I'm having problems connecting it to the nrfCloud.
Since I'm using it in Austria, I'm using a different sim card on...